new SNES ic diagram

Turbo Tax 1.0 · Post by **Turbo Tax 1.0** » Sun Feb 18, 2007 1:26 pm

much better that my last one

Master of Portables · Post by **Master of Portables** » Sun Feb 18, 2007 2:00 pm

thank you !, i already firgured out the wires that go to the snes, but diagram before didn't have the dent, so i wired it backwards...anyway, i have it correct now, but i am on a break so the controller will be wired to the ic later...

Rellizate · Post by **Rellizate** » Sun Feb 18, 2007 2:38 pm

I'm sure this will be usefull to some people. Maybe to me, if I can get a snes mini.

ATOMICMAN · Post by **ATOMICMAN** » Wed Apr 18, 2007 8:26 am

any resistors needed for this? or can you solder the tact leads directly to the ic and run back to the ground?

Post by **Triton** » Wed Apr 18, 2007 10:57 am

very hand man, i had the old one cleaned up a bit but now it has the colored wire locations too, thanks!

Turbo Tax 1.0 · Post by **Turbo Tax 1.0** » Wed Apr 18, 2007 1:18 pm

ATOMICMAN wrote:any resistors needed for this? or can you solder the tact leads directly to the ic and run back to the ground?

it works without them, but for some reason donkey country wont work with the controller on my mkII

ATOMICMAN · Post by **ATOMICMAN** » Wed Apr 18, 2007 1:59 pm

Turbo Tax 1.0 wrote:
ATOMICMAN wrote:any resistors needed for this? or can you solder the tact leads directly to the ic and run back to the ground?
it works without them, but for some reason donkey country wont work with the controller on my mkII

uber sweetness. makes things so much easier. too bad the ics cant be easily found oem without buy in bulk =(

Kurt_ · Post by **Kurt_** » Wed Apr 18, 2007 2:08 pm

They ARE easily found in SNES Controllers!

And as for Donkey Kong Country, mine works fine without everything.

ATOMICMAN · Post by **ATOMICMAN** » Wed Apr 18, 2007 2:10 pm

Kurt_ wrote:They ARE easily found in SNES Controllers!

And as for Donkey Kong Country, mine works fine without everything.

desoldering... urgue... to... kill... rising...

just annoying...

but i can deal.

Kurt_ · Post by **Kurt_** » Wed Apr 18, 2007 2:31 pm

If you're talking about the IC's, I just chipped the IC section out and super-glued it onto a board.

Post by **gannon** » Wed Apr 18, 2007 3:02 pm

Yep, that way you can include the discrete resistance section of the PCB that's in the controller.

nuky nuclear · Post by **nuky nuclear** » Tue Jul 01, 2008 10:03 pm

this will really help me out when i go to wire the controller, just a few questions, what are the red, white, yellow, orange, and brown mean? and also how would i connect the newly rewired controller to the board and does it matter what size wires i use? also i am assuming that the diagram is of the pinout thing that is in the controller to start with corrent?

Turbo Tax 1.0 · Post by **Turbo Tax 1.0** » Tue Jul 01, 2008 10:27 pm

just the colors of the wires on the snes controller here http://www.gamesx.com/controldata/snesdat.htm

just use either ide cable or 22gauge wire

nuky nuclear · Post by **nuky nuclear** » Wed Jul 02, 2008 12:04 pm

another question, do i attach the the white, yellow, orange, red, and brown wires directly to the place where the controller port like this?