- Before opening
- Just cracked it open
- Removed memory card block, lazer, and currently removing power board
- All done I cleaned everything up from here on
W.I.P Ps1 Case mod based on 77' Trans am
Moderator: Moderators
-
darkcloud990
- Posts: 19
- Joined: Thu Dec 11, 2008 9:38 pm
W.I.P Ps1 Case mod based on 77' Trans am
Well hello everyone, I have been wanting to do a case mod for a long time now and I'm finally getting around to it. Today I have stripped down my Ps1 and have taken pictures which I will have uploaded. I am new to this so I may need to ask a few questions and what not, in fact my first one being what sand paper would be best for the Ps1 and how to go about sanding it? Now aside from that this is a case mod for the Ps1 based on the 77' Trans am paint scheme which was black with gold trim. This will try to represent that the best I can. Now for some pictures.
- Before opening
- Just cracked it open
- Removed memory card block, lazer, and currently removing power board
- All done I cleaned everything up from here on
- Before opening
- Just cracked it open
- Removed memory card block, lazer, and currently removing power board
- All done I cleaned everything up from here on
-
sonic4freedom
- Portablizer
- Posts: 158
- Joined: Sat Jan 26, 2008 7:54 am
- Location: burlington NJ, US
Re: W.I.P Ps1 Case mod based on 77' Trans am
Whats up Craig? its Chris! Can't wait to see your progress. I'm going to be watching this thread! 
SS I miss your old Profile PicturesShockSlayer wrote:Jarate ftw. Shards of glass in your eyes, piss all over you, and someone is about to kill you. What a way to die.
-----------------
The Rising Portablizer
-
darkcloud990
- Posts: 19
- Joined: Thu Dec 11, 2008 9:38 pm
Re: W.I.P Ps1 Case mod based on 77' Trans am
Hey Chris, It's been along time. Glad you came by, I'll hopefully get it going this weekend.
-
ttsgeb
- Posts: 155
- Joined: Mon Feb 25, 2008 9:19 pm
- 360 GamerTag: ttsgeb
- Steam ID: ttsgeb
- Location: behind you, don't look, I'll just be behind you.
Re: W.I.P Ps1 Case mod based on 77' Trans am
Smokey and the Crash Bandicoot themed?
I would suggest 400-600 grit to prep for painting, then 800-1000 between coats.
What do you plan to do for the screaming chicken...
You DO plan to include the screaming chicken, right? RIGHT?
I would put the screaming chicken on the disk cover, then cut windows on the sides, except I would make them like it's a t-top, where you can pull a cover off to see in and such.
I would suggest 400-600 grit to prep for painting, then 800-1000 between coats.
What do you plan to do for the screaming chicken...
You DO plan to include the screaming chicken, right? RIGHT?
I would put the screaming chicken on the disk cover, then cut windows on the sides, except I would make them like it's a t-top, where you can pull a cover off to see in and such.
-
darkcloud990
- Posts: 19
- Joined: Thu Dec 11, 2008 9:38 pm
Re: W.I.P Ps1 Case mod based on 77' Trans am
Thank you for the advice on the sandpaper, And yes the t-top would be bad ass but I'm only a beginner so I'm not even sure how this is going to turn out. I'll put up a picture depicting where the colors are going to be. Maybe get some feedback.ttsgeb wrote:Smokey and the Crash Bandicoot themed?
I would suggest 400-600 grit to prep for painting, then 800-1000 between coats.
What do you plan to do for the screaming chicken...
You DO plan to include the screaming chicken, right? RIGHT?
I would put the screaming chicken on the disk cover, then cut windows on the sides, except I would make them like it's a t-top, where you can pull a cover off to see in and such.