If you're making a portable you probably need something to watch it on. (Unless you want to guess what's happening in the game, but I wouldn't advise that) Anyway, this forum is your "Hacking a pocket TV/screen" one-stop solution. Share your experiences and knowledge here.
Moderator: Moderators
tappan
Posts: 66 Joined: Sun Dec 05, 2004 5:59 pmLocation: Erehwon, AR
Contact:
Post
by tappan Sun Dec 12, 2004 7:26 pm
What is the diameter of the board for the screen?
Last edited by
tappan on Tue Dec 14, 2004 8:54 pm, edited 1 time in total.
I keep cutting it off.. and it's still too short.
someone
Posts: 708 Joined: Tue Apr 27, 2004 7:34 pmLocation: California, Bay Area
Post
by someone Sun Dec 12, 2004 11:45 pm
i think its about 6-7 inches ill measure it sometime....
tappan
Posts: 66 Joined: Sun Dec 05, 2004 5:59 pmLocation: Erehwon, AR
Contact:
Post
by tappan Tue Dec 14, 2004 8:56 pm
Anyone have any more exact measurements?
I keep cutting it off.. and it's still too short.
SpongeBuell
Senior Member
Posts: 5190 Joined: Wed Apr 07, 2004 10:52 amLocation: Colorado
Contact:
Post
by SpongeBuell Tue Dec 14, 2004 9:02 pm
I would wait until you get the screen, that way you can get the exact measurements of the exact screen you'll get, especially with different revisions of mobos and stuff.
Life of Brian wrote: RYW wrote: RYW:
I'll be honest with you - I would have never guessed that.
tappan
Posts: 66 Joined: Sun Dec 05, 2004 5:59 pmLocation: Erehwon, AR
Contact:
Post
by tappan Tue Dec 14, 2004 9:10 pm
Thanks for the quick response spongebuell.
I keep cutting it off.. and it's still too short.
SpongeBuell
Senior Member
Posts: 5190 Joined: Wed Apr 07, 2004 10:52 amLocation: Colorado
Contact:
Post
by SpongeBuell Tue Dec 14, 2004 9:20 pm
I'm here all the time, and I reply when I can
Life of Brian wrote: RYW wrote: RYW:
I'll be honest with you - I would have never guessed that.
deiol
Posts: 58 Joined: Mon Nov 22, 2004 8:32 pm
Post
by deiol Wed Dec 15, 2004 8:26 am
tappan wrote: I may end up getting a gamecube/third party screen.
I was going to get a gamecube screen, but JackFrost told me they're crap.
HK-47
Moderator
Posts: 3598 Joined: Thu Jul 15, 2004 2:17 pmLocation: /dev/moderator/
Contact:
Post
by HK-47 Wed Dec 15, 2004 3:04 pm
deiol wrote: tappan wrote: I may end up getting a gamecube/third party screen.
I was going to get a gamecube screen, but JackFrost told me they're crud.
Psone screens are FAR superior. I had a gc screen and it broke. The psone screen ROCKS! Get it!
HK-47
Moderator
Posts: 3598 Joined: Thu Jul 15, 2004 2:17 pmLocation: /dev/moderator/
Contact:
Post
by HK-47 Wed Dec 15, 2004 4:37 pm
That happened to me a while ago... When I only had 20 or so posts...
HK-47
Moderator
Posts: 3598 Joined: Thu Jul 15, 2004 2:17 pmLocation: /dev/moderator/
Contact:
Post
by HK-47 Wed Dec 15, 2004 4:40 pm
Maybe not then, but it was a while ago...
someone
Posts: 708 Joined: Tue Apr 27, 2004 7:34 pmLocation: California, Bay Area
Post
by someone Wed Dec 15, 2004 7:47 pm
tappan wrote:
they are, i got a ghetto-1337 INTEC <<OMFG screen and the pos had bad graphics and it broke...
riva16
Posts: 204 Joined: Sat Nov 13, 2004 12:11 pmLocation: Michigan
Contact:
Post
by riva16 Mon Dec 20, 2004 10:24 am
It's 5 6/8" wide, and 5 1/4" top to bottom... Really close, not exact... I just remembered I had to trim the side of the board a small bit for it to fit in my portable... Just give yourself 6" wide, 6" long to make room for the plugs too...
Hope that helps ya out!
Hope that helps ya out!