A/V pinout

gamer2 · Post by **gamer2** » Wed Jun 22, 2005 12:05 am

hello,
What is the pin out of the AV module on the N64 board? left to right on the front.
thank you

nos_slived · Post by **nos_slived** » Wed Jun 22, 2005 12:16 am

http://abbibi.cogia.net/video.php

gamer2 · Post by **gamer2** » Wed Jun 22, 2005 12:01 pm

ahh so it is abbibi.cogia.net for doom portables, i got i bits of info thak you

gamer2 · Post by **gamer2** » Wed Jun 22, 2005 1:35 pm

could NIN^_^NIN's pin out work?

on the top of NIN^_^NIN

nos_slived · Post by **nos_slived** » Wed Jun 22, 2005 2:00 pm

I don't think so, because that is for PAL. I would suggest going with the one on PoD.

gamer2 · Post by **gamer2** » Wed Jun 22, 2005 2:42 pm

ok just need to know
and knowing is half the battle......GI JOE!

gamer2 · Post by **gamer2** » Wed Jun 22, 2005 8:13 pm

so it is
o= pin

o o o o o o
1 2 3 4 5 6

o o o o o o
7 8 9 10 11 12

1.Audio (L)
2.compasite Video
3.Luma (what is that)
4.GND
5. Composite Sync (RGB)
6. 200 uf capacitor (rgb) Red
7. Audio (R)
8. NOT USED
9. Chroma (what is that)
10. GND
11. 200 uf Capacitor (RGB) blue
12. 200 uf Capacitor (RGB) Green

is that about right and do i need the RGB stuff if my N64 isnt RGB modded
or if i do it with out the mod will it ruin my N64

nos_slived · Post by **nos_slived** » Wed Jun 22, 2005 10:51 pm

If your N64 doesn't have RGB out, the 200uF caps do absolutely nothing. They are for strengthening the RGB lins, but do squat is you don't use RGB. Luma and Chroma are for S-Video. There is a small error in the picture, because only pin 4 is ground. If you go to the bottom of the screen, pin 10 is actually +5V. Don't forget that this is looking at the multiout from the back of your N64. Here is the pinout that you will require:
1. Audio (L)
2. composite Video
3. NOT USED
4. NOT USED
5. NOT USED
6. NOT USED
7. Audio (R)
8. NOT USED
9. NOT USED
10. NOT USED
11. NOT USED
12. NOT USED

gamer2 · Post by **gamer2** » Wed Jun 22, 2005 10:57 pm

ok that is all the soldering i need ok
to me that sounds like a waste of a few good pins

is pin 10 a way to power the screen?

nos_slived · Post by **nos_slived** » Wed Jun 22, 2005 11:06 pm

Pin 10 is only 5V, and it is tied to the 7805, which has a 1A max output, so I wouldn't try it. Pin 10 is okay to use for a couple LEDs, but no high draw electronics.

gamer2 · Post by **gamer2** » Wed Jun 22, 2005 11:07 pm

ok now i know
and Knowing is Half the battle

GI JOE

gamer2 · Post by **gamer2** » Thu Jun 23, 2005 12:16 am

so the pins go

0 0 0 0 0 0
6 5 4 3 2 1

0 0 0 0 0 0
12 11 10 9 8 7

nos_slived · Post by **nos_slived** » Thu Jun 23, 2005 12:34 am

On the plug and from the inside of the N64(on the back of the multiout), but if you look at the back of the N64, it will be the picture I posted.

BTW, as soon as I get my second 64 open(hopefully tomorrow), I am going to test pins 4 and 10, because of that small error on PoD.

gamer2 · Post by **gamer2** » Thu Jun 23, 2005 12:43 am

so i was right on the first time for the inside of the N64

nos_slived · Post by **nos_slived** » Thu Jun 23, 2005 12:45 am

0 0 0 0 0 0
6 5 4 3 2 1

0 0 0 0 0 0
12 11 10 9 8 7

That is the inside.