Where do I connect LED's - (Vent lighting)
Moderator:Moderators
Hi,
I am trying to add LED's to illuminate the vents on my N64. I have already switched the standard red LED for a blue one, but now want to get some light coming out of the vents. Where on the board to I attach these? I want to attach them after the switch so that they are only on when the N64 is on.
I dont have much knowledge of technical terms so can try and be as clear as possible Looking forward to your replies!
Note:
I made a post the yesterday to ask what was wrong with my other N64. Well I have since bought another one and have repeated the exact same thing on this one and it works fine (except I couldn't get vent LED's to light up ). So it appears that my other N64 is faulty but I will keep it for spares.
I am trying to add LED's to illuminate the vents on my N64. I have already switched the standard red LED for a blue one, but now want to get some light coming out of the vents. Where on the board to I attach these? I want to attach them after the switch so that they are only on when the N64 is on.
I dont have much knowledge of technical terms so can try and be as clear as possible Looking forward to your replies!
Note:
I made a post the yesterday to ask what was wrong with my other N64. Well I have since bought another one and have repeated the exact same thing on this one and it works fine (except I couldn't get vent LED's to light up ). So it appears that my other N64 is faulty but I will keep it for spares.
Re: Where do I connect LED's - (Vent lighting)
I have trawled the internet looking for guides on this, I cant find anything
hopefully some one can give me some advice asap because I want to get cracking with it lol.....I'm a fisherman and yet very impatient when it comes to this.
Thanks in advance
hopefully some one can give me some advice asap because I want to get cracking with it lol.....I'm a fisherman and yet very impatient when it comes to this.
Thanks in advance
Re: Where do I connect LED's - (Vent lighting)
Measure around with a multimeter, looking for a 3.3v supply - there is a pin onthe back labeled 3.3v, solder from there to ground.
-
- Posts:1000
- Joined:Sat Jan 30, 2010 12:22 am
- PSN Username:Haunted360
- 360 GamerTag:Haunted 360
- Location:Australia
- Contact:
Re: Where do I connect LED's - (Vent lighting)
LOL.
There is a RED LED (as mine is - PAL / Europe) already on the board.
Just solder to that.
If not, then yes. Solder to the 3.3 Volt line (as long as you have a 3 Volt LED that is).
There is a RED LED (as mine is - PAL / Europe) already on the board.
Just solder to that.
If not, then yes. Solder to the 3.3 Volt line (as long as you have a 3 Volt LED that is).
Re: Where do I connect LED's - (Vent lighting)
I had found the 3.3v line and the pin labelled 3.3v but the trouble is connecting to this spot leaves the LED on continually providing the N64 is plugged in. I was hoping to find one after the switch....which I did in the end, I just probed around until I found a suitable spot like I said....not much experience lolSnipeye wrote:Measure around with a multimeter, looking for a 3.3v supply - there is a pin onthe back labeled 3.3v, solder from there to ground.
Re: Where do I connect LED's - (Vent lighting)
haha i hooked mine up before the switch but then i just added a switch on the side and it worked out fine
Re: Where do I connect LED's - (Vent lighting)
Try what haunted said, that LED is operated via the power switch, and you can just solder to the LED pins already on the board.
Re: Where do I connect LED's - (Vent lighting)
Thanks I found a point of 3.3v just after the switch at the controller ports 1 & 2 so connected them there. And then found another going to the right hand side controllers port 3 & 4 and connected the other half here. Ran them all back to the ground. Works great!Bush wrote:Try what haunted said, that LED is operated via the power switch, and you can just solder to the LED pins already on the board.
I couldn't run all of my LED's off the spot where the red stock LED is already placed. I could only run a maximum of 2 LED from this point for some reason.....
All sorted now, looks great
- SackAttack
- Posts:7
- Joined:Mon Oct 11, 2010 12:54 am
Re: Where do I connect LED's - (Vent lighting)
Did you tie any resistors to the led's when you soldered them to the board?
Re: Where do I connect LED's - (Vent lighting)
No I didn't, I am confident that they don't need one attached. Its all working fine right now, so I guess if it goes wrong I will know why.
Thanks for pointing that out though
Thanks for pointing that out though