A few 'parting words' if you will

demonofaj · Post by **demonofaj** » Sun Nov 06, 2005 3:36 pm

Well, last wee bit o help before I finish up el PSONE of mine. So...I've noticed that for the disc to spin, some button on the mobo needs to be pressed to keep it going. I put on the lid (unscrewed) with a taken off disc lid, and it doesn't spin. So does the lid need to be closed for the thing to keep on spinning. Atka, can you help.

shmagoogin77 · Post by **shmagoogin77** » Sun Nov 06, 2005 4:01 pm

lets see some pics

daguuy · Post by **daguuy** » Sun Nov 06, 2005 4:04 pm

there should be a little button that the lid pushes when it closes. maybe your lid is meesed up or needs to be screwed to push hard enough because it's not on all the way

nos_slived · Post by **nos_slived** » Sun Nov 06, 2005 4:13 pm

If I remember correctly, it's a PBNO, so tying the pins together should allow for open spinning.

demonofaj · Post by **demonofaj** » Mon Nov 07, 2005 3:46 pm

Can I solder the two pins together which the switch gives out, and permanently connect it with wire.

daguuy · Post by **daguuy** » Mon Nov 07, 2005 3:47 pm

yes, but make sure you don't turn it on without a CD with the lid open

demonofaj · Post by **demonofaj** » Mon Nov 07, 2005 3:48 pm

So it's true, Sony is the true W.M.D.. My disc lid won't click, close, but it's closed nonetheless.

Mr. Cool · Post by **Mr. Cool** » Mon Nov 07, 2005 4:52 pm

demonofaj wrote:Can I solder the two pins together which the switch gives out, and permanently connect it with wire.

Its easier just to put some hot glue on the thing the lid presses down on, to keep it down. tape works too, but not as well

demonofaj · Post by **demonofaj** » Mon Nov 07, 2005 5:15 pm

I shortened my wire by splicing it and reconnecting color coded wires, like green to green and such. However, the wire is like '100 in one' whereas one side is say 75 the other 51. Is their a warning level for the siganl on the wires to go.

THANKS FOR ALL THE HELP!

demonofaj · Post by **demonofaj** » Mon Nov 07, 2005 9:20 pm

Bumpidity, in the disc drives 'laser transperency cable' the place where it plugs into the mobo, I find two weird sheets of paper in the port. Are they important? If so do I need to put it back in when I put the ribbon cable in again? Thanks.

demonofaj · Post by **demonofaj** » Tue Nov 08, 2005 3:47 pm

CRAP, a triple post. Anyways, I opened the mobo off the case, but the switch has TWO rows of pins. Which ones should I connect. If you say bottom, to me bottom means the one twoard the controller ports.

demonofaj · Post by **demonofaj** » Wed Nov 09, 2005 2:54 pm

*Shake*

Come on guys, I need help, and I'm VERY unclear about it...

demonofaj · Post by **demonofaj** » Thu Nov 10, 2005 5:01 pm

ATKA, thank you sooooo much. Your wiring tip worked, NOW I CAN JUST PUT IT TOGETHER! And then I'll make my LAST THREAD about completion. Thanks guys, thanks soooo much.

Kayleigh57020 · Post by **Kayleigh57020** » Wed Dec 28, 2005 8:22 am

daguuy wrote:yes, but make sure you don't turn it on without a CD with the lid open

Post by **bicostp** » Wed Dec 28, 2005 9:18 am

Please read the rules and abide to them, Kayleigh57020. Don't bring up old threads for no reason.

This thread is unofficially locked. We're going on the honor system for this one. Please treat this thread as locked until a PSX/32-Bit mod officially locks it. Thank you.