Introducing the Darth 64....... Youtube Video Added

[hailrazer]

Allow me to introduce my apprentice ................

DARTH 64

*edit* Added a youtube video :
http://www.youtube.com/watch?v=66gd9CKCWAU







This of course is a N64 portable. I named it the Darth 64 because my kids say it resembled the Darth Vader helmet they have

I wanted a system that was bulletproof. I bought some from this site and the build quality was shaky to say the least. Hot glue just wasn't an option.

So I used a case that I could mold into what I wanted but could still be put back together with screws. All integrated plastic parts were ABS Cement melted and fused to the original case, then hard filler bumper epoxy was used then soft fill bumper epoxy for the finishing touches.

The N64 motherboard was attached using plastic stand-offs that were Abs cemented and epoxied in. Then the cart slot was attached to the motherboard with l-brackets and nuts/bolts.

So everything is rock solid. Shake it or drop it and nothing will come loose or rattle.

List of features:
Psone screen with original backlight.
Flush mounted headphone jack.
5000maH Li-Poly batteries with quick charger and protection circuit.
Gamecube style joystick and d-pad.
Rear shoulder buttons and twin z buttons.
Cart slot relocation.

All I have left to do is wet sand the case and polish it in 7 days after the paint is dry.

Here's how it all started and went down.

[hailrazer]

First of all I was at a Fle Market and found an interesting portable. It was called the Lazer Doodle. Thought to myself..."Hmm I might could do something with this



Here's a comparison of the case next to a Game Case:



A picture of the back and guts :





And with the guts out



No here's the construction log

[hailrazer]

I started out like I mentioned wanting a SOLID handheld. So I decided to try a technique not used much.

For plastic if you use normal epoxy and Bondo spot putty, it can and usually will crack.

So I used ABS Cement to fuse the parts like the screen, controller, etc to the case. Then I used Plastic Bumper Epoxy Hard filler to fill major gaps and fuse it together even more. :

http://www.urethanesupply.com/mm5/merch ... ode=2020-T

Then I use Plastic Bumper Flexible Filler as the "spot putty" to finish it off smoothe and crack free for life.

http://www.urethanesupply.com/mm5/merch ... ode=2000-T

Please note in the following pics I decided to abandon the white piece and add the controller later.

The process is pretty easy. You cut the parts for as close a fit as possible. Then put a spot or three of hot glue to hold the part in place. Tape the backside of the case for large gap areas. The I use a cue tip , dip it in the Abs cement and drip it in between the two parts. It adheres pretty quick. I let it dry in front of a fan for an hour then do it again to fill in missing gaps. Let it dry about 2-3 hours, flip it over and remove the tape and then using the cue tips drip in the Abs Cement REALLY thick on the backside. Now let it dry for a couple of days.





After a couple of days sand down the Abs plastic on the front side with 36-40 grit sandpaper until it is smooth and level, don't worry about low spots.




Now it's time to move on to the hard filler. Mix it and apply it liberally in the areas you need to fill and mold. It dries in 15 minutes and you can sand it down. Use 36-40 grit paper and sand it down real good and as smooth as you can get it.





To be continued.............

[hailrazer]

Now move on to the flexible filler. Fill in the low spots and feather out to a flat finish. After it dries in 15 minutes sand it down with 40 grit. You will probably have to do that a time or two. Once it is smooth with no dips move up to 80 grit , then 180 grit, then 320 grit , then 600 grit until it is baby butt smooth.



Now put a coat of primer on and look at the flaws :



Now don't be bashful. Sand it down as smooth as you can get it on the bad spots. Add small amounts of flex filler , let dry and using 80 or 180 grit paper sand it down super smooth , then move on to 320 grit then 600 grit.



Hopefully after doing this 2-3 times you will have this :



Now a few more construction notes:

[hailrazer]

For the controller I wanted something small and better than the original.

So I went for the Hori MiniPad. It has about the same setup as the Gamecube, in fact it basically uses the same joystick, and layout.

Here it is next to a N64 controller.



For the back trigger buttons I wanted something different and an old Ps1 pad came to the rescue :



And how I put it in :





I was originally going to have a flip up cart slot but it was to much stress on the cart slot wires so I went with a more standard cart relocation. :





And here's how it turned out :




Continue on

[hailrazer]

Now like I said I wanted it to be solid.

For that reason the N64 board needed to be mounted solid. So I Abs cemented and epoxied four standoffs in the case:



Now I could solidly mount the N64 board. Also I wanted a solid cart slot. So I used L brackets to mount them to the heatsink/rf shielding, then I bolted that to the N64 motherboard.



I used 2 Li-Poly 5000mah batteries with smart charger and protection circuit.

Here is everything wired together :



And with the battery cover and cart slot cover in place :

[hailrazer]

I also flush mounted a headphone jack and added the power charging jack :



And I used the built in power switch :



And of course the finished pics as you've seen :

The back didn't turn out as smooth as I wanted but I was running out of time

[hailrazer]

That looks really nicely done and the case is an interesting twist from the usual suspects. You've obviously thought out the design because the insides look as though they fit together really nicely. I heard the Hori Pad Mini's joystick is more sensitive than the standard controller. Have you noticed this much?

I haven't really noticed a difference between it and the Original N64 sticks except that the joystick is much nicer and smoother. More sensitive in what way exactly ?

[Sun-Wukong]

Damn...

In a good way.

[Nurd!]

Cool.
Is it easy to hold?

Aren't those controllers like 35 dollars?

[hailrazer]

Cool.
Is it easy to hold?

Aren't those controllers like 35 dollars?

It's easy to hold but easier for larger hands

No the controllers are $50 shipped.

Here's what I have invested :

N64 --- $15
Psone Lcd --- $20
Hori GamePad --- $50
Li-Poly batteries --- $75
Paint and supplies --- $35
Epoxy/Abs --- $50

Total ------- $240

LOTS OF TIME !!!!!!!!!!!

[bacteria]

Nice job and nice guide. Nice to see something "a bit different".

[SoccerSkater93]

How much to buy one???
That is a BEAUTIFUL portable

[hailrazer]

Thanks for the compliments.

Here's a pic of how I hold it with my small hands

I just hold it normal and use my trigger fingers to hold the case and my middle fingers on the thumbsticks.

[grossaffe]

That's some good work, there. pretty damn good franken-casing.