NesP Progression Thread (1st Portabilization)
Moderator:Moderators
- HotDog-Cart
- Portablizer
- Posts:3804
- Joined:Sat Jul 16, 2005 12:07 pm
- PSN Username:Lythinca
- Steam ID:scythe_king
- Location:Your IP Address, Connecting...
- Contact:
- Sharp Sapphire
- Portablizer
- Posts:415
- Joined:Fri Feb 22, 2008 9:40 pm
- Dr. KillGood
- Senior Member
- Posts:2209
- Joined:Sat Jan 21, 2006 1:03 am
- Location:Earth
- bicostp
- Moderator
- Posts:10491
- Joined:Mon Mar 07, 2005 5:47 pm
- Steam ID:bicostp
- Location:Spamalot
- Contact:
It does.
AMD makes / made more than just x86 clones, you know. (So does Intel, for that matter.)
AMD makes / made more than just x86 clones, you know. (So does Intel, for that matter.)
Twitter
http://www.pcwgaming.com" onclick="window.open(this.href);return false;
If you want a Dropbox account, please use my referral link
http://www.pcwgaming.com" onclick="window.open(this.href);return false;
If you want a Dropbox account, please use my referral link
- hailrazer
- Portablizer Extraordinaire
- Posts:2764
- Joined:Mon Jul 10, 2006 8:57 pm
- Location:Georgia Sweet Georgia
$20 shipped:Zereo_XI wrote:Can anyone post a link for a good affordable ( =<50$ ) screen. The only one I found was a 80$ Xbox Zenith. Thanks in advance.
http://cgi.ebay.com/ws/eBayISAPI.dll?Vi ... %26fvi%3D1
hailrazer- Thanks, I was not getting anything cause I was always writing Zenith in the search bar.
bacteria- I know it pretty gay wire, I will try to get something else. When I'm soldering and it takes a bit to long it start to melt.
bacteria- I know it pretty gay wire, I will try to get something else. When I'm soldering and it takes a bit to long it start to melt.
My portable thread:
Not stating any project again until I have a job.
Not stating any project again until I have a job.
Ok, nothing makes you look more like a generic teenager than using the word "gay" to describe completely non-homosexual things.Zereo_XI wrote:I know it pretty gay wire,
A better way to say it might be "a bad choice of wiring medium" or "inappropriate material". If you give the ol' "That's too nerdy for me to say", then you don't belong in a place where consoles are hacked.
That sounded way harsher than I intended, but it really ticks me off when people do that.
That said, I suggest against making the cart slot stick out perpendicular to the portable.
...
Sorry about that. Yes, I will definitely not make it perpendicular to the board.
The reason I'm Relocating the slot is:
1.My 72 pin Connector wasn't working anymore (Original Catridge side).
2. Easier to have a smaller casing since you can put the PCB flat against the case. (Normally, everything on the PCB wouldn't allow the C slot to exit all the way out of the case).
Since I don't want the game to be sticking out, would putting it horizontal be a good idea?
The reason I'm Relocating the slot is:
1.My 72 pin Connector wasn't working anymore (Original Catridge side).
2. Easier to have a smaller casing since you can put the PCB flat against the case. (Normally, everything on the PCB wouldn't allow the C slot to exit all the way out of the case).
Since I don't want the game to be sticking out, would putting it horizontal be a good idea?
My portable thread:
Not stating any project again until I have a job.
Not stating any project again until I have a job.
But uh, the cart slot slides off, and you can just buy a new one and put it back exactly where it is without soldering.Zereo_XI wrote:Sorry about that. Yes, I will definitely not make it perpendicular to the board.
The reason I'm Relocating the slot is:
1.My 72 pin Connector wasn't working anymore (Original Catridge side).
2. Easier to have a smaller casing since you can put the PCB flat against the case. (Normally, everything on the PCB wouldn't allow the C slot to exit all the way out of the case).
Since I don't want the game to be sticking out, would putting it horizontal be a good idea?
...