I need help with my xbox 360 laptop
Moderator:Moderators
-
- Posts:10
- Joined:Wed Mar 23, 2011 9:29 pm
I am 14 years old and am well on my way to creating an xbox 360 laptop. Only I have one major or minor problem. I was going to see if my xbox 360 would turn of correctly with all green rings after I have extended and soldered the front USB port. So I turned the xbox on and I get two red rings while I have the hard drive, fans, DVD drive and ring of light chip plugged in. I know that it is not overheating because the motherboard is out of the case. Though there might be one problem. Though I am not experienced at soldering I am mediocre. While I was soldering I noticed that a very small trace on the motherbord was torn and not connected to it's right pin port. It was bent into the air. If this USB ports traces are not connected does this cause two red rings. Any help would be appreciated. Thank you.
-
- Posts:44
- Joined:Fri Oct 17, 2008 9:56 pm
- Contact:
I need help with my xbox 360 laptop
Are your heatsinks on and properly attached? Can we see a picture of the trace that was lifted?
Hackify me cap'n!
- humakabula1
- Posts:728
- Joined:Sun May 30, 2010 3:11 am
- 360 GamerTag:H1writer
- Location:Diggi Down Under
Re: I need help with my xbox 360 laptop
There are heatsinks on the chips right?
you have thermal paste on the chip?
your using fans?
you have thermal paste on the chip?
your using fans?
Wedgix (custom linux distro): 20% complete
-
- Posts:10
- Joined:Wed Mar 23, 2011 9:29 pm
Re: I need help with my xbox 360 laptop
There are no heatsinks on the unit at all or no thermal paste but the board is in open air. Do the heatsinks need to be on the chip.?
-
- Posts:10
- Joined:Wed Mar 23, 2011 9:29 pm
Re: I need help with my xbox 360 laptop
Can I only place the heatsinks on or do I need thermal paste and xclamps.
-
- Posts:10
- Joined:Wed Mar 23, 2011 9:29 pm
Re: I need help with my xbox 360 laptop
I am uploading a video to youtube I will put the link here once it uploads.
- humakabula1
- Posts:728
- Joined:Sun May 30, 2010 3:11 am
- 360 GamerTag:H1writer
- Location:Diggi Down Under
Re: I need help with my xbox 360 laptop
you need the thermal paste
Wedgix (custom linux distro): 20% complete
-
- Posts:44
- Joined:Fri Oct 17, 2008 9:56 pm
- Contact:
I need help with my xbox 360 laptop
The heatsinks are definitely needed and they need to be secured. Either with xclamps or screws. And thermal paste isnt 100% necessary for testing purposes. But you need thermal paste when you're closing the unit up.
Hackify me cap'n!
-
- Posts:10
- Joined:Wed Mar 23, 2011 9:29 pm
Re: I need help with my xbox 360 laptop
Thank you for all of your input. How would I screw in the hetsinks by the way.
- humakabula1
- Posts:728
- Joined:Sun May 30, 2010 3:11 am
- 360 GamerTag:H1writer
- Location:Diggi Down Under
Re: I need help with my xbox 360 laptop
lolwut.rickylago2 wrote:The heatsinks are definitely needed and they need to be secured. Either with xclamps or screws. And thermal paste isnt 100% necessary for testing purposes. But you need thermal paste when you're closing the unit up.
yes it is, you risk damaging the hardware if you dont
Wedgix (custom linux distro): 20% complete