Page 1 of 3
Reference Standard Sprites
Posted: Thu May 07, 2009 3:02 pm
by jjhammerstein
No need to put everything in the same forum!
Here are some that have been done already:
I'll be doing a few, feel free to contribute yourself!
Re: Reference Standard Sprites
Posted: Thu May 07, 2009 8:27 pm
by Mario
Looks awesome! Is this for making schematics?
Re: Reference Standard Sprites
Posted: Thu May 07, 2009 8:36 pm
by Skyone
Mmhmm.
More to come.
Re: Reference Standard Sprites
Posted: Thu May 07, 2009 9:16 pm
by jjhammerstein
I've gone right ahead and done the N64 mobo with every capacitor, resistor, and IC. All the ICs have the correct number of pins and everything. I have labels on the caps and crystals, but not the resistors or ICs. Someone want to lend some names?
A few final touches and I'll post it sometime tomorrow morning.
Re: Reference Standard Sprites
Posted: Thu May 07, 2009 10:26 pm
by Skyone
Electrolytic*
Sounds awesome, jjhammerstein.
Re: Reference Standard Sprites
Posted: Fri May 08, 2009 6:28 am
by jjhammerstein
Skyone wrote:Electrolytic*
I don't see anything. What are you talking about?
EDIT:
Annnnnd, here's the N64 board. I can change it if someone has ideas.
Adding it to the first post too.
Re: Reference Standard Sprites
Posted: Fri May 08, 2009 8:48 am
by Tibia
That is some amazing spritework. I salute you! It looks great!
Re: Reference Standard Sprites
Posted: Fri May 08, 2009 9:36 am
by jjhammerstein
Thank you! I hope it proves useful!
Re: Reference Standard Sprites
Posted: Fri May 08, 2009 9:54 am
by bacteria
Nice artwork. Clean.
Re: Reference Standard Sprites
Posted: Fri May 08, 2009 10:17 am
by jjhammerstein
Can someone provide the text on the ICs? I'm working off of a picture that isn't quite the resolution I would like.
Re: Reference Standard Sprites
Posted: Fri May 08, 2009 10:40 am
by marshallh
Crystals aren't yellow and the RDRAM chips only have 4 pins going to VCC on the bottom
Re: Reference Standard Sprites
Posted: Fri May 08, 2009 10:44 am
by jjhammerstein
Okay, I'll change it. Did you make the lower crystal bigger on purpose?
Re: Reference Standard Sprites
Posted: Fri May 08, 2009 10:47 am
by marshallh
Forgot to finish drawing that one
Edit as you wish. The chip text is 98% accurate though. There was also half of the chip next to the reset button that got left behind, I erased it. It matches the PCB on my desk right now. This should be the same for revisions 01-05.
Re: Reference Standard Sprites
Posted: Fri May 08, 2009 10:58 am
by jjhammerstein
Good?
I don't know why, but the crystals looked coppery in the picture. The picture had the heatsink still on, so I assumed that the RAM was symmetrical, thanks for the fix. Is there anything else that you think I should put into the drawing? I kinda picked out the things that looked important, but I don't really know anything. I'm hoping to use this to make a direct-to-board cart relocation guide, are there any pictures that show where I need to mark connections? I can trace some... traces... if otherwise. Are all of the connections on the top of the board? I don't want to draw the bottom, it's so complicated.
Re: Reference Standard Sprites
Posted: Fri May 08, 2009 12:17 pm
by marshallh
Whoops, looks like you forgot it again XD