Search found 266 matches

by ToastBucket
Sun Mar 14, 2010 11:14 am
Forum: 1990's Gaming
Topic: Elephant64 Worklog
Replies: 36
Views: 6365

Re: Elephant64 Worklog

What I did was extremely inefficient. I drilled small holes at the base of the buttons, stripped some solid wire, and put it through and down through the perf board. I then bent it over when the button was at the highest position i wanted to be like. What I would suggest is to cut out the bits from ...
by ToastBucket
Sat Mar 13, 2010 3:15 pm
Forum: 1990's Gaming
Topic: what is PCB
Replies: 11
Views: 1679

Re: what is PCB

nachoz12341 wrote:they are so your batteries are protected from over charge and under charge
/discharge
by ToastBucket
Sat Mar 13, 2010 2:26 pm
Forum: 1990's Gaming
Topic: Elephant64 Worklog
Replies: 36
Views: 6365

Re: Elephant64 Worklog

My screen is not outputting any sound. I think Its because the volume is all the way down and I can't change it...I relocated the volume and brightness buttons but they aren't working. The tact switches are connected to the same places that the orignals were by some IDE cable but NONE of the switche...
by ToastBucket
Fri Mar 12, 2010 7:22 pm
Forum: 1990's Gaming
Topic: Controller
Replies: 7
Views: 991

Re: Controller

I just checked...Amazon ships to Australia.

http://www.amazon.com/gp/offer-listing/ ... ition=used" onclick="window.open(this.href);return false;
by ToastBucket
Fri Mar 12, 2010 10:09 am
Forum: Portable Screen Hacking
Topic: 7" LCD
Replies: 8
Views: 1680

Re: 7" LCD

But they teach you to read. :wink:
by ToastBucket
Fri Mar 12, 2010 9:45 am
Forum: Portable Screen Hacking
Topic: 7" LCD
Replies: 8
Views: 1680

Re: 7" LCD

You know with all these datamaxs your buying you should at least be able to read a little
by ToastBucket
Fri Mar 12, 2010 8:54 am
Forum: 1990's Gaming
Topic: SuperPad 64 joystick mod. Gamecube stick inside :)
Replies: 20
Views: 13338

Re: SuperPad 64 joystick mod. Gamecube stick inside :)

What I would do is get a small piece of relatively thick foam or just some plastic and cut it to a good size to go imbetween the Z and POT. or you could just run some uninsulated wire (Solid) across them and hot glue them down to the case so that the stay in place.
by ToastBucket
Fri Mar 12, 2010 8:51 am
Forum: Portable Screen Hacking
Topic: 7" LCD
Replies: 8
Views: 1680

Re: 7" LCD

hailrazer wrote:Third one has no inputs so it is a no-go.

2nd one is a Pyle . EVERY Pyle I own or have owned looks like complete crap. So I'd pass on that one.
The third one says in the picture it has AV in.

and thanks for the info :)
by ToastBucket
Fri Mar 12, 2010 12:49 am
Forum: Portable Screen Hacking
Topic: 7" LCD
Replies: 8
Views: 1680

7" LCD

I was looking around and stumbled across these. Does anyone know if they're any good? http://cgi.ebay.com/NEW-Intec-Color-Game-Screen-Portable-Wii-FREE-SHIP_W0QQitemZ120518613305QQcmdZViewItemQQptZVideo_Games_Accessories?hash=item1c0f781939" onclick="window.open(this.href);return false; http://cgi.e...
by ToastBucket
Thu Mar 11, 2010 11:39 pm
Forum: 1990's Gaming
Topic: SuperPad 64 joystick mod. Gamecube stick inside :)
Replies: 20
Views: 13338

Re: SuperPad 64 joystick mod. Gamecube stick inside :)

The red wires are just positive lines and the black one is a ground line. The red ones are interchangeable or you could just use one and bridge them like the ground is. I'm not sure why there are two positive lines because there doesn't need to be. VD1 stands for voltage and VC1 stands for common me...
by ToastBucket
Thu Mar 11, 2010 9:45 pm
Forum: 1990's Gaming
Topic: Elephant64 Worklog
Replies: 36
Views: 6365

Re: Elephant64 Worklog

Well I think it's about time for a new iron....I can probably finish this project with the one I have now because there is very minimal soldering left to do, but my iron has completely oxidized. Stupid wet sponge. I want a station but theyre expensive. :( I'm also going to get a desoldering iron and...
by ToastBucket
Thu Mar 11, 2010 9:37 pm
Forum: 1990's Gaming
Topic: SuperPad 64 joystick mod. Gamecube stick inside :)
Replies: 20
Views: 13338

Re: SuperPad 64 joystick mod. Gamecube stick inside :)

HA...while writing the above comment that mentions check the attached pic for a diagram, I thought to myself that it was probably going to forget to attach the pic. And I did. So here it is!
by ToastBucket
Thu Mar 11, 2010 9:35 pm
Forum: 1980's Gaming
Topic: Portacom (portable famicom) Help needed!
Replies: 6
Views: 1618

Re: Portacom (portable famicom) Help needed!

If your using a NOAC you can go a lot smaller than AG-85 or ZN-40. Shockslayer's putting an N64 into an AG-64. But if you don't want to cram it all into a small case the former two are great, comfortable cases.
by ToastBucket
Thu Mar 11, 2010 9:30 pm
Forum: 1990's Gaming
Topic: SuperPad 64 joystick mod. Gamecube stick inside :)
Replies: 20
Views: 13338

Re: SuperPad 64 joystick mod. Gamecube stick inside :)

Little bump here for probably a noob question (sorry :/) I'm attempting at doing this mod with the SuperPad 64 (by Performance) same one as the black one in the picture above. When rewiring the GC c-stick to the super pad, is it ok to just rip off the 4 white wires that connect the C-stick board to...
by ToastBucket
Thu Mar 11, 2010 9:17 pm
Forum: 1990's Gaming
Topic: Need Help Wiring Gamecube Joystick
Replies: 7
Views: 1519

Re: Need Help Wiring Gamecube Joystick

http://kyorune.com/modding/article.php?id=82" onclick="window.open(this.href);return false;

I couldn't get this to work but here you go.

Oh and make sure your x axis is on top...doesn't work on bottom for some reason (at least it didn't for me) probably resistance inconsistancy