Search found 631 matches

by kasar
Thu Nov 14, 2013 12:10 pm
Forum: 2000's Gaming
Topic: The definitive GC motherboard trimming guide
Replies: 6
Views: 12822

Re: The definitive GC motherboard trimming guide

images are dead D:
by kasar
Thu Nov 22, 2012 6:11 pm
Forum: GameCube & Wii
Topic: GameCube Portable Guide "How To and FAQ"
Replies: 159
Views: 88636

Re: GameCube Portable Guide "How To and FAQ"

* 23/11/2012 - added Internal controller and external controller port switch diagram to the guide by user request.
by kasar
Sat Aug 04, 2012 12:17 pm
Forum: GameCube & Wii
Topic: GameCube Portable Guide "How To and FAQ"
Replies: 159
Views: 88636

Re: GameCube Portable Guide "How To and FAQ"

nope, in my case I used a european gamecube and screen. I had to adjust the variable resistor to get rid of the bad image quality, since the signal was too strenght and it was almost white. you can try without a resistor, and if you notice the image have the sysmtoms mentionated before, use a variab...
by kasar
Fri Aug 03, 2012 12:37 pm
Forum: GameCube & Wii
Topic: GameCube Portable Guide "How To and FAQ"
Replies: 159
Views: 88636

Re: GameCube Portable Guide "How To and FAQ"

So how do i connect the psone screen if i dont have the resistor in my av cable? is it ok that i took out the AV conector port?( gamecube mother board) then connect the yellow wire directly without using a resistor. some people told me the resistor is only avalible at the european cables. anyway, i...
by kasar
Sun Jul 29, 2012 9:15 am
Forum: GameCube & Wii
Topic: GameCube Portable Guide "How To and FAQ"
Replies: 159
Views: 88636

Re: GameCube Portable Guide "How To and FAQ"

yeah, you can use any battery wich meet the minimal specs, and that camera battery does ^^ all you need is locate the + and - pins and wire them to the system. you also will need to design a charge way if you dont want to use its original camera to charge it ;) mmm, not sure about the psone screen b...
by kasar
Sun Jul 22, 2012 2:17 pm
Forum: GameCube & Wii
Topic: GameCube Portable Guide "How To and FAQ"
Replies: 159
Views: 88636

Re: GameCube Portable Guide "How To and FAQ"

that battery should be ok. it also already have PCB so you can charge it safetly. to charge it, you should use a little more voltage of the battery capacity. if the battery is 14.8v you can try recharging with 16 or 17 volts. I also used a 14.8v battery pack for my old project, it was a laptop batte...
by kasar
Sun Jul 22, 2012 5:14 am
Forum: GameCube & Wii
Topic: GameCube Portable Guide "How To and FAQ"
Replies: 159
Views: 88636

Re: GameCube Portable Guide "How To and FAQ"

@GCPX2.0 never bought one of those. anyway you can try on places such this one http://www.chipspain.com/en/consoles-451/nintendo-wii-115/development-and-backups-wii-120/wii-modchips-193/wiikey-fusion-3438.html" onclick="window.open(this.href);return false; I also recomend you get this, for less sold...
by kasar
Sat Jul 14, 2012 9:18 am
Forum: GameCube & Wii
Topic: GameCube Portable Guide "How To and FAQ"
Replies: 159
Views: 88636

Re: GameCube Portable Guide "How To and FAQ"

yeah, as far I know, it is compatible with all gamecubes who have a DD connection (basically all of them ^^) yeah, you can hook the fan and power switch board directly to the battery, that fan is rated for 12v, I supose it will also handle 14.8v and a little higher maybe, but dont push more since it...
by kasar
Fri Jul 13, 2012 3:33 pm
Forum: GameCube & Wii
Topic: GameCube Portable Guide "How To and FAQ"
Replies: 159
Views: 88636

Re: GameCube Portable Guide "How To and FAQ"

mmm, are you sure? I though all gamecube Disk Drive were the same ones, except the panasonic Q (wich is very rare), the revisions of the gamecube only have a different motherboard (with some ports stripped and with the regulator board integrated in some cases, but no more differences as far I know) ...
by kasar
Thu Jul 12, 2012 3:48 pm
Forum: GameCube & Wii
Topic: GameCube Portable Guide "How To and FAQ"
Replies: 159
Views: 88636

Re: GameCube Portable Guide "How To and FAQ"

mmm, I tried soldering with ethernet cables and my experience was bad, those cables didnt didnt even pick the tin properly, I remember I used a some kind of cable with several colored cables inside, it worked fine for the DD reallocation and controller hacking. well, relating the ide cable, I never ...
by kasar
Wed Jul 11, 2012 9:10 pm
Forum: GameCube & Wii
Topic: GameCube Portable Guide "How To and FAQ"
Replies: 159
Views: 88636

Re: GameCube Portable Guide "How To and FAQ"

yeah, using the gameboy player is perfectly posible on a portable. however you will have extra work with wires, space placing it on the case and it will make your portable bigger. mmm, as far I know there are not any special cable wich allow direct extension from gbplayer conector to gamecube. but y...
by kasar
Sun Jul 08, 2012 9:22 pm
Forum: GameCube & Wii
Topic: GameCube Portable Guide "How To and FAQ"
Replies: 159
Views: 88636

Re: GameCube Portable Guide "How To and FAQ"

mmm, I think I used a 35W or 45W soldering iron, not sure. however I think is not recomended to apply heat more than 1-2 secs at the trace in order to prevent trace peel or any other electronic burning. that is why is that important to keep the soldering iron head allways clean and plated color, a c...
by kasar
Sun Jul 08, 2012 5:02 am
Forum: GameCube & Wii
Topic: GameCube Portable Guide "How To and FAQ"
Replies: 159
Views: 88636

Re: GameCube Portable Guide "How To and FAQ"

well, after reading this http://www.made-by-bacteria.com/viewtopic.php?f=60&t=79" onclick="window.open(this.href);return false; I will reconsiderate my opinion about the zenith screen. try getting that zenith screen, (with the ps1/ps2 inputs) so you can ensure it will work. you can also give a read ...
by kasar
Sat Jul 07, 2012 1:23 pm
Forum: GameCube & Wii
Topic: GameCube Portable Guide "How To and FAQ"
Replies: 159
Views: 88636

Re: GameCube Portable Guide "How To and FAQ"

hey GCPX2.0 thanks for using this guide ^_^ relating your battery question. I supose the battery voltage is 12v or superior, else it will have some problems with the stock regulator board. there are some methods to power the whole system with lower voltages, like SS discovered, but it is easier to j...
by kasar
Sat Jun 02, 2012 11:37 am
Forum: 2000's Gaming
Topic: My first portable gamecube !
Replies: 14
Views: 17759

Re: My first portable gamecube !

oh, yeah, the money ^_^ well, in my case that is why I used a laptop battery pack, tweaked it to work with the portable and used the original laptop as charger ^_^ it even let me play while charging :) well, dont worry, you dont need to make another portable if you find a cheap/nice battery pack, yo...