* Login 
* FAQ    * Search

All times are UTC - 6 hours




Post new topic Reply to topic  [ 8 posts ] 
Author Message
 Post subject: My PSOne screen is diferent!
PostPosted: Sat Sep 25, 2010 9:46 am 
Offline

Joined: Sat Sep 25, 2010 9:01 am
Posts: 4
I get an original psone screen but it's diferent from de used un ben's book. There are two components in the place used to plug the resistor of the LEDS, so i don't know where to plug it. I need some help please.
Image
Ignore the red circle. The components are those two gray little cylinder near the volume button.


Top
 Profile E-mail  
 
 Post subject: Re: My PSOne screen is diferent!
PostPosted: Sat Sep 25, 2010 10:58 am 
Offline
User avatar

Joined: Thu Oct 15, 2009 8:51 pm
Posts: 58
Location: Rosario
r u talking about the capacitors?

_________________
Image


Top
 Profile E-mail  
 
 Post subject: Re: My PSOne screen is diferent!
PostPosted: Sat Sep 25, 2010 11:12 am 
Offline

Joined: Sat Sep 25, 2010 9:01 am
Posts: 4
I think so...
Here is the ben's book picture:
Image


Top
 Profile E-mail  
 
 Post subject: Re: My PSOne screen is diferent!
PostPosted: Sun Sep 26, 2010 2:23 pm 
Offline
User avatar

Joined: Mon Mar 05, 2007 7:20 pm
Posts: 1382
Location: Sunny California
You can put the resistor anywhere; it doesn't matter where it goes. Just wire it correctly and you'll be fine.

Also, don't use a 10ohm resistor. Use 100ohms.

_________________
Image


Top
 Profile  
 
 Post subject: Re: My PSOne screen is diferent!
PostPosted: Sun Sep 26, 2010 5:02 pm 
Offline

Joined: Sat Sep 25, 2010 9:01 am
Posts: 4
Thanks Mario. The LED's are connected in series right? And I still use a 100ohms resistor if I use 4 LED's instead 3?


Top
 Profile E-mail  
 
 Post subject: Re: My PSOne screen is diferent!
PostPosted: Sun Sep 26, 2010 5:08 pm 
Offline
Moderator
User avatar

Joined: Sat Sep 10, 2005 2:17 pm
Posts: 2975
Location: here and there
That guide is wrong-if you do it according to that method you'll hurt the LEDs and they start flickering.


Put a 33ohm resistor in series with each LED. Then put 3/4 of those in parallel.

_________________
Image


Top
 Profile  
 
 Post subject: Re: My PSOne screen is diferent!
PostPosted: Sun Sep 26, 2010 5:30 pm 
Offline

Joined: Sat Sep 25, 2010 9:01 am
Posts: 4
Hum... Ok, thanks. Other question, where is the ground in the PAL screen?


Top
 Profile E-mail  
 
 Post subject: Re: My PSOne screen is diferent!
PostPosted: Mon Oct 04, 2010 6:49 am 
Offline

Joined: Sat Jan 30, 2010 12:22 am
Posts: 1000
Location: Australia
The Ground (Common Ground) on the Screen, is usually easily found where the Screw Posts are / went through.

It should be easy to see...


Top
 Profile E-mail  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 

All times are UTC - 6 hours


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group