I'm needing a kick harness adaptor made for my Excalibur Supergun to have controller ports 3&4 to work for multi-player arcade boards and 6-button Capcom Fighting games. If my friend is unable to get the parts to make it then I can try here.
Here are some of my Excalibur Supergun Pics,
These male and female ports on the side are for the kick harness adaptor.
Need a kick harness adaptor made for my Excalibur Supergun
Moderator:Moderators
- Shawn Carr2o
- Posts:7
- Joined:Sun Feb 06, 2011 11:02 am
- Location:San Jose CA
- Contact:
Re: Need a kick harness adaptor made for my Excalibur Supergun
While I am unfamiliar with the particulars I am willing to try.
Could you describe the pinout/wiring required in greater detail?
Could you describe the pinout/wiring required in greater detail?
- Shawn Carr2o
- Posts:7
- Joined:Sun Feb 06, 2011 11:02 am
- Location:San Jose CA
- Contact:
Re: Need a kick harness adaptor made for my Excalibur Supergun
I'm not to good at describing the details but I can have my friend Lios/Zeon who built my Supergun unit to send me instructions on the pinout/wiring to make it and I'll pm it to you?Snow_Cat wrote:While I am unfamiliar with the particulars I am willing to try.
Could you describe the pinout/wiring required in greater detail?
Re: Need a kick harness adaptor made for my Excalibur Supergun
Sounds reasonible.
Re: Need a kick harness adaptor made for my Excalibur Supergun
I have compiled the pinouts to the auxilary/option/kick harnesses from the manuals (copies availble upon request) into this table for easy comparison.
I have translated "button", "shoot" and "shot" to push, omitted the word "switch", and made the designations uniform for readibility.
I am going to email the builder to confirm the internal wiring between auxiliary 2 and the controller ports, but there may be a compatibility issue with the Sammy in 4 player mode, where input from players using the last 3 buttons would adversely affect each other...
docs.google.comkick.htm
Could someone contribute the pitch sizes, with pics if possible?
I have translated "button", "shoot" and "shot" to push, omitted the word "switch", and made the designations uniform for readibility.
I am going to email the builder to confirm the internal wiring between auxiliary 2 and the controller ports, but there may be a compatibility issue with the Sammy in 4 player mode, where input from players using the last 3 buttons would adversely affect each other...
docs.google.comkick.htm
Could someone contribute the pitch sizes, with pics if possible?
Re: Need a kick harness adaptor made for my Excalibur Supergun
docs.google.com2011.03.06.pdf
I drew this so that I wouldn't mess up the component layout, then I put the buttons and connector on the wrong sides of the board when I built it- there will be a delay while disassemble and reassemble it.
The group of three buttons next to the CPSII socket switch between 2 and 4 player mode. The two buttons control the volume.
There are only three buttons (1/A,2/B,3/C) connected in four player mode due to the internal limitations of the Excalibur Supergun.
There is no conflicting connections between controllers.
Seperate buttons instead of a multiplexor was used because I had buttons on hand.
I drew this so that I wouldn't mess up the component layout, then I put the buttons and connector on the wrong sides of the board when I built it- there will be a delay while disassemble and reassemble it.
The group of three buttons next to the CPSII socket switch between 2 and 4 player mode. The two buttons control the volume.
There are only three buttons (1/A,2/B,3/C) connected in four player mode due to the internal limitations of the Excalibur Supergun.
There is no conflicting connections between controllers.
Seperate buttons instead of a multiplexor was used because I had buttons on hand.
Re: Need a kick harness adaptor made for my Excalibur Supergun
docs.google.com2011.03.27.pdf
Four versions of a CPS1-to-2 Kick/Aux-Harness Passthrough-Adaptor, derived from the design by Jamma-Nation-X.com.
From top-to-bottom;
Meowing:
Four versions of a CPS1-to-2 Kick/Aux-Harness Passthrough-Adaptor, derived from the design by Jamma-Nation-X.com.
From top-to-bottom;
- 2-player design Cloned (:<) directly from Jamma-Nation-X.com
- 2-player design cloned with 180° flip
- 2/4-player design with 180° flip
- 2/4-player design with out 180° flip (double sided design)
Meowing:
Spoiler: