SNES Arcade Cabinet
Moderator:Moderators
- Punchinello
- Posts:27
- Joined:Tue Jun 29, 2004 2:14 pm
I want to do something similar to this:
http://www.willyliliana.com/NES%20Cabin ... abinet.htm
but with an SNES... and without the short shorts.
I will be able to get my hands on a cabinet, mount the console on the inside with an opening for the cartridge.
Now here is the problem. I originally planned on using the SNES Super Advantage for the controller. (lol, pics):
This would be pretty easy as these things are all over ebay for about $10 a pop. I figured I could just mount two of these bad boys on the cabinet, or take out the chip and build it into the cabinet.
Then I got to thinking. I saw this on one of those "build your own cabinet" websites. http://arcadecontrols.com/arcade_achilles.shtml
So basically, I really want to build my own controls using buttons and an 8 way joystick from a regular SNES controller that works on the SNES like an SNES controller.
Now after that long winded back story, my question is: would it be very difficult to turn an SNES pad into an arcade joystick like in the link above? Can I just soulder some buttons onto the pad or is there more to it than that? Thanks!
http://www.willyliliana.com/NES%20Cabin ... abinet.htm
but with an SNES... and without the short shorts.
I will be able to get my hands on a cabinet, mount the console on the inside with an opening for the cartridge.
Now here is the problem. I originally planned on using the SNES Super Advantage for the controller. (lol, pics):
This would be pretty easy as these things are all over ebay for about $10 a pop. I figured I could just mount two of these bad boys on the cabinet, or take out the chip and build it into the cabinet.
Then I got to thinking. I saw this on one of those "build your own cabinet" websites. http://arcadecontrols.com/arcade_achilles.shtml
So basically, I really want to build my own controls using buttons and an 8 way joystick from a regular SNES controller that works on the SNES like an SNES controller.
Now after that long winded back story, my question is: would it be very difficult to turn an SNES pad into an arcade joystick like in the link above? Can I just soulder some buttons onto the pad or is there more to it than that? Thanks!
alright I recommen this
The SNES advantage has everything you need, however, If you just want buttons without all the other features, Seriously vasriable turbos...wimpy wimpy wimpy
All you need to do is connect the live feed for each button to one pole of the switch and the ground on the other, then you just go from there, I say this since the little chips in the SNES can be removed easily and re-wired easily and they take up nearly no space when compared to an arcade cab
However, if you want the trubo features, then you have two options, do the afoirmentiond and biuld your own circuits...hard
or possibly use the SNES advantage...waste of a good controller IMO
~Krepticor
The SNES advantage has everything you need, however, If you just want buttons without all the other features, Seriously vasriable turbos...wimpy wimpy wimpy
All you need to do is connect the live feed for each button to one pole of the switch and the ground on the other, then you just go from there, I say this since the little chips in the SNES can be removed easily and re-wired easily and they take up nearly no space when compared to an arcade cab
However, if you want the trubo features, then you have two options, do the afoirmentiond and biuld your own circuits...hard
or possibly use the SNES advantage...waste of a good controller IMO
~Krepticor
I refuse to dignify myself with an intelligent and witty signature
- Punchinello
- Posts:27
- Joined:Tue Jun 29, 2004 2:14 pm
So basically, I can just use an SNES controller chip, buy the button switches, and connect 2 wires from the buttons to the chip... for each button on the pad. Am I getting that correct? I realize that there are specific places I need to wire, but theres not other circuity involved beside re routing the switch (or button) that is normally part of the controller to the arcade style button?
- Punchinello
- Posts:27
- Joined:Tue Jun 29, 2004 2:14 pm
So this seems like it could be fairly easy. I apologize though, because I don't really know too much about electronics yet, but I am studying engineering at a university right now, so learning shouldn't be that difficult. Could you please elaborate a little? I am not sure what you mean by common ground.
if you look closely at those pictures you will see the gamepad board and the microswitches from the buttons/joystick. you also see all the wires connecting them. the pads for the buttons on the pcb has 1 wire soldered to it which connects to the microswitch. if you then look at the microswitches, you will see that they are interconnected by another wire as well. that is the common ground. it is shared among all the microswitches as well as the board normally. so, in this case, since the ground is all the same, you can either solder a ground wire for each individual button, or connect all the buttons and solder 1 or 2 ground wires. (in theory 1 will work fine, but i say 2 because it is a better practice to do a "ground loop" in arcade controls by having 1 wire ground the button switches and 1 wire ground the joystick switches even though they are all connected to eachother.)
the microswitches usually have 3 contacts, so you need to keep them straight. one is for ground or commin, (on the bottom), and the two on the back of the switch are either "normally closed" or "normally open". connect the "normally open" to the pcb at the appropriate pads.
it really is pretty straightforward. just study those pictures and read up some at arcadecontrols.com if you wish. you will learn that most gamepads work in the same way -- i have 4 of the old style ps1 pads i was planning on doing this with.
- Punchinello
- Posts:27
- Joined:Tue Jun 29, 2004 2:14 pm
I did practically the same thing, but with a keyboard. It works great, and the SNES controller idea is what I'm planning on doing with an XBox controller on my current project. Solder the wires from the buttons to the pads on the IC. You can check out the pics of my arcade buttons connected to a keyboard encoder. I got the buttons and joystick from happs controls.
http://www.nucklez.com/arcade/
http://www.nucklez.com/arcade/
Re: SNES Arcade Cabinet
sorry,, i know im digging up an old thread.. and asking a lot for a newbie.. but ive recently purchased a cabinet and a retro duo(can order joysticks/buttons/wires next week) and desperately need to figure out exactly how to wire up my snes controller to some happ joysticks/buttons.. i can see in the diagram above how to connect all the buttons and joystick wires to the board with no problems.. its just im not so sure about the ground wires.. i can see that you connect it to all of the ground/common on the microswitches for the buttons.. but i cant see much about the ground wires on the joystick to d-pad.. where do i ground the loop to? the d-pad? or is there something close to it? i just cant tell in the small images.. i am new to wiring and soldering, so any help would be much appreciated. though, a simple diagram showing the ground and lead wires in different colors would be wonderful.
the reason i need to be real sure is because im on a tight budget, and really dont want to mess something up.
ive searched for a few days trying to find a good diagram about doing this.. and all ive really found is this thread and one video on youtube: http://www.youtube.com/watch?v=OPvRdYPmJNM" onclick="window.open(this.href);return false;
i got some useful info from the video, and i want my finished product to be similar... but it still dont really show how to wire up the ground all the way.
im also gonna try make a tutorial about putting one of these together.. ill give you total credit for helping with the wiring.
heres the cab i got for $40.. gotta make tv braces, back door and control panel(that i know how to do)
the reason i need to be real sure is because im on a tight budget, and really dont want to mess something up.
ive searched for a few days trying to find a good diagram about doing this.. and all ive really found is this thread and one video on youtube: http://www.youtube.com/watch?v=OPvRdYPmJNM" onclick="window.open(this.href);return false;
i got some useful info from the video, and i want my finished product to be similar... but it still dont really show how to wire up the ground all the way.
im also gonna try make a tutorial about putting one of these together.. ill give you total credit for helping with the wiring.
heres the cab i got for $40.. gotta make tv braces, back door and control panel(that i know how to do)
http://mylittlegamer.blogspot.com/" onclick="window.open(this.href);return false;